If you’re in need of a reliable PLCC socket for your industrial or scientific application, look no further – we’ve got you covered. In this article, we’ll answer 10 of the most frequently asked questions about PLCC sockets, so you can make the best decision for your needs.
Table of Contents
What is a PLCC socket
A PLCC socket is a type of integrated circuit socket used for mounting surface-mount PLCC (plastic leaded chip carrier) devices. They are frequently used in the electronics industry for a variety of applications. PLCC sockets are available in a wide range of sizes and pin counts to accommodate different PLCC devices.
PLCC sockets are designed to provide a secure connection between a PLCC device and a printed circuit board (PCB). They typically have two or four rows of pins that mate with the leads on the PLCC device. The number of pins varies depending on the specific PLCC device being used.
PLCC sockets are classified as either through-hole or surface-mount devices. Through-hole PLCC sockets are designed to be mounted on the PCB from the top side, while surface-mount PLCC sockets are designed to be soldered onto the PCB from the bottom side.
PLCC sockets are typically made from a variety of materials, including plastic, metal, or ceramic. They may also be plated with gold or other metals to improve electrical conductivity and/or prevent corrosion.
PLCC sockets are an important part of many electronic devices and circuits. They provide a reliable connection between the PLCC device and the PCB, which is essential for proper operation of the device.
What are the dimensions of a PLCC socket
PLCC sockets come in a variety of sizes and dimensions, depending on the specific PLCC chip that is being used. The most common dimensions for a PLCC socket are 3.3mm x 3.3mm, 4.4mm x 4.4mm, and 5.5mm x 5.5mm. Each of these dimensions corresponds to a different pitch, or distance between the pins on the chip. PLCC chips with a pitch of 0.5mm use the 3.3mm x 3.3mm dimension socket, while those with a pitch of 0.8mm use the 4.4mm x 4.4mm socket. Finally, PLCC chips with a pitch of 1.27mm use the 5.5mm x 5.5mm socket.
What is the pin count of a PLCC socket
A PLCC socket is a type of integrated circuit (IC) socket that is used to connect a PLCC chip to a circuit board. It is characterized by a certain number of pins, which can range from 20 to 84, depending on the specific PLCC socket. The pin count of a PLCC socket therefore refers to the number of pins that are present on the socket, which is used to determine its compatibility with a particular PLCC chip.
How much current can a PLCC socket handle
PLCC sockets are designed to handle a maximum current of 1.5A.
What is the maximum operating temperature of a PLCC socket
A PLCC socket is a type of chip carrier, which is a device used to hold and electrically connect an integrated circuit (IC) to a printed circuit board (PCB). They are commonly used in applications where space is limited, such as in portable electronics. The maximum operating temperature of a PLCC socket is the temperature at which the socket can safely operate without damaging the IC or PCB.
How much voltage can a PLCC socket handle
When it comes to voltage, there is no one-size-fits-all answer to the question of how much a PLCC socket can handle. The amount of voltage that a particular PLCC socket can take will depend on its design and construction. However, in general, most PLCC sockets can handle up to 60 volts without any problems. Some PLCC sockets are even rated for higher voltages, such as 120 volts.
What is the contact resistance of a PLCC socket
PLCC sockets are used in a variety of electronic devices, from computers to cell phones. They are also used in many industrial and military applications. The contact resistance of a PLCC socket is the measure of the electrical resistance between the socket’s contacts and the device’s pins. The lower the contact resistance, the better the electrical connection between the socket and the device.
What is the insulation resistance of a PLCC socket
The insulation resistance of a PLCC socket is the electrical resistance between the socket and the surrounding environment. It is typically measured in ohms and is a key factor in determining the safe operating voltage of the socket. The insulation resistance of a PLCC socket is typically much higher than that of a standard electrical outlet, making it an ideal choice for high voltage applications.
What is the dielectric withstanding voltage of a PLCC socket
A dielectric withstanding voltage, or DWV, is a measure of a material’s ability to insulate against an electric field. The dielectric withstanding voltage of a PLCC socket is the maximum voltage that can be applied to the socket without causing electrical breakdown.
Is a PLCC socket RoHS compliant
All products that fall under the RoHS directive must not contain more than 0.1% of certain restricted materials by weight. A PLCC socket is a type of integrated circuit (IC) socket, and therefore must comply with the RoHS standards. Many manufacturers of PLCC sockets are compliant with RoHS, and will clearly state this on their product pages or in their datasheets. If you are unsure whether a particular PLCC socket is RoHS compliant, you can contact the manufacturer directly.